问ds18b20例程（DS18B20的程序）

大家好,小东方来为大家解答以上的问题。ds18b20例程，DS18B20的程序这个很多人还不知道,现在让我们一起来看看吧！

1、接上18B20温度传感器后数码管显示出当前温度#include #define uchar unsigned char#define uint unsigned intsbit DS=P2^2; //define interfaceuint temp; // variable of temperatureuchar flag1; // sign of the result positive or negativesbit dula=P2^6;sbit wela=P2^7;unsigned char code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d, 0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71};unsigned char code table1[]={0xbf,0x86,0xdb,0xcf,0xe6,0xed,0xfd, 0x87,0xff,0xef};void delay(uint count) //delay{ uint i; while(count) { i=200; while(i>0) i--; count--; }}///////功能:串口初始化,波特率9600。

2、方式1///////void Init_Com(void){ TMOD = 0x20; PCON = 0x00; SCON = 0x50; TH1 = 0xFd; TL1 = 0xFd; TR1 = 1;}void dsreset(void) //send reset and initialization command{ uint i; DS=0; i=103; while(i>0)i--; DS=1; i=4; while(i>0)i--;}bit tmpreadbit(void) //read a bit{ uint i; bit dat; DS=0;i++; //i++ for delay DS=1;i++;i++; dat=DS; i=8;while(i>0)i--; return (dat);}uchar tmpread(void) //read a byte date{ uchar i,j,dat; dat=0; for(i=1;i<=8;i++) { j=tmpreadbit(); dat=(j<<7)|(dat>>1); //读出的数据最低位在最前面。

3、这样刚好一个字节在DAT里 } return(dat);}void tmpwritebyte(uchar dat) //write a byte to ds18b20{ uint i; uchar j; bit testb; for(j=1;j<=8;j++) { testb=dat&0x01; dat=dat>>1; if(testb) //write 1 { DS=0; i++;i++; DS=1; i=8;while(i>0)i--; } else { DS=0; //write 0 i=8;while(i>0)i--; DS=1; i++;i++; } }}void tmpchange(void) //DS18B20 begin change{ dsreset(); delay(1); tmpwritebyte(0xcc); // address all drivers on bus tmpwritebyte(0x44); // initiates a single temperature conversion}uint tmp() //get the temperature{ float tt; uchar a,b; dsreset(); delay(1); tmpwritebyte(0xcc); tmpwritebyte(0xbe); a=tmpread(); b=tmpread(); temp=b; temp<<=8; //two byte compose a int variable temp=temp|a; tt=temp*0.0625; temp=tt*10+0.5; return temp;}void readrom() //read the serial{ uchar sn1,sn2; dsreset(); delay(1); tmpwritebyte(0x33); sn1=tmpread(); sn2=tmpread();}void delay10ms() //delay { uchar a,b; for(a=10;a>0;a--) for(b=60;b>0;b--); }void display(uint temp) //显示程序{ uchar A1,A2,A2t,A3,ser; ser=temp/10; SBUF=ser; A1=temp/100; A2t=temp%100; A2=A2t/10; A3=A2t%10; dula=0; P0=table[A1]; //显示百位 dula=1; dula=0; wela=0; P0=0x7e; wela=1; wela=0; delay(1); dula=0; P0=table1[A2]; //显示十位 dula=1; dula=0; wela=0; P0=0x7d; wela=1; wela=0; delay(1); P0=table[A3]; //显示个位 dula=1; dula=0; P0=0x7b; wela=1; wela=0; delay(1);}void main(){ uchar a; Init_Com(); do { tmpchange(); // delay(200);for(a=10;a>0;a--) { display(tmp()); } } while(1);}。

本文到此分享完毕，希望对大家有所帮助。